Mac Emulator Sheepshaver10/8/2021
As of late, development has been focussed on Windows and Mac OS X, but pre-built Debian packages have appeared for 64bit and 32bit Ubuntu installations too. You can find it on Amazon for SheepShaver is basically a PowerPC emulator that fakes an entire PowerPC-based Macintosh in software so that you can run MacOS 7.5.2 through 9.0.4 on Windows, Mac OS X, Linux, and BeOS. I use the iBuffalo SNES controller. You can configure a wii mote or a usb controller, too.Updated: now works on Yosemite. Hypercard in SheepShaver emulator. Even though SheepShaver can run earlier versions, I’m focussing on MacOS 9.0.4.Running a Hypercard stack on a modern Mac.
![]() ![]() Emulator Sheepshaver Software So ThatI’m sure there’s a more clever way to work around this problem, but I haven’t really looked into this yet.Update: Thanks to OSNews reader nalf38, there’s a solution. In other words, be careful, and don’t run it on a production machine – your SheepShaver environment has root access. Before we start, on my machine, SheepShaver had to be run as root, or else I’d get a “Cannot map Low Memory Globals: Operation not permitted” error. You can find these ROMs online too, but again, that is most likely illegal.Once you have all these, it’s pretty darn easy to get going. Again, I’m lucky in that I have two of these, so I didn’t have to jump through a lot of hoops. Of course, there’s always the option of going the way of the pirate, but this is most likely illegal in your country of residence.The third thing you’ll need is a little trickier to come by: you’re going to need the ROM image of a new world Mac, like a PowerMac G4. The steps to set up this environment will look remarkably familiar to anyone with experience in running virtual machines.First, we need to create an image file to act as a hard drive for MacOS 9. Now you can run SheepShaver without root privileges.After launching SheepShaver (I simply use a terminal to execute sudo SheepShaver), you’ll be confronted with the settings window which also happens to act as the launcher for your MacOS 9 environment. Then execute service procps start. It is important to set the “UNIX root” field to a safe directory, like your home directory or a specially created share directory. Since you first need to install MacOS 9, insert your MacOS 9.0.4 disk, enable the CD-ROM driver, and set the “Boot from” drop-down to “CD-ROM”. You obviously need to tell SheepShaver where to store this file I stored mine on my free-for-all Data partition, and called it MacOS.Now it’s time to correctly set everything up. I didn’t touch the JIT compiler tab at all.Now you can press “Start” to launch the virtual machine, and if all goes correctly, you’ll be asked to initialise the hard drive image you made. You might want to set this value a little lower if you have less RAM to play with (I have 4GB). I allocated 256MB of RAM to the virtual machine, which is more than enough for MacOS 9. In the serial/network tabs, be sure to set the Ethernet interface drop-down to slirp (we’ll set up networking within MacOS 9 later), and I guess memory/misc is pretty much self-explanatory. I didn’t change anything in the keyboard/mouse tab, since it all seems to work just fine with the default settings. Note that if you used the solution detailed in the update above, you can discard this warning.You can play with the graphics/sound tab to find the settings that fit you – I have MacOS 9 running in a 1024×768 window. I was really looking forward to trying out the new Classilla browser, but sadly, I get a very weird memory error when trying to launch it, so it was back to iCab for me. Note, however, that the browsers which ship with MacOS 9 (Internet Explorer, Netscape) will crash your virtual machine, so you’ll have to either use Classilla or iCab. You now have your own working MacOS 9 environment.To set up networking, you have to go to the TCP/IP preferences panel, and set the values exactly as pointed out below in the screenshot. Once complete, shut the live CD down, and change the appropriate settings in the SheepShaver window so you’ll boot from the hard drive image (I disabled the CD-ROM driver altogether). The installation routine is fairly straightforward. ![]() Slathered with utterly moronic transparency effects (e.g. In Windows I’ve generally stuck with the good old grey and blue Windows Classic theme, and chosen applications that fit in with that rather than using non-standard skins, but that’s harder and harder to accomplish.For example Opera (with its Windows Native theme) used to be nice and simple and consistent, but with 10.5 that’s now designed for the flashy, standards free world of Windows Vista/7. It may look boring at a glance, but it’s lovely to use.Of course there’s in option of skins in modern operating systems, but it’s harder to fix every application. All the applications fit together consistently without them all having their own ugly skins. Nothing distracting, nothing that wastes loads of space or damages usability purely to look cool. It’s the way everything seems to be going, but that doesn’t mean that I have to like it.
0 Comments
Leave a Reply.AuthorAira ArchivesCategories |